Kawasaki J300 - Service manual > Seat, Fairings

Seat

Seat Removal

• Open the seat.
• Remove the nuts [A].

• Remove:
  Nuts [A]
  Seat Assy [B]

Seat Installation

• Installation is the reverse of removal.

Storage Box Removal

• Remove:
  Seat (see Seat Removal)
  Bolts [A]
  Nuts [B]

• Disconnect the storage box light switch lead connectors [A].
• Remove the storage box [B].

Storage Box Installation

• Installation is the reverse of removal.

Fairings

Lower Fairing Removal

• Remove:
  Floor Mat
  Rear Fairing Cover (see Rear Faring Cover Removal)
  Screws [A]

• Remove the quick rivets [A].

• Remove the bolt [A].
• Pull the rear side of the lower fairing outward [B] to clear the hooks [C], and then pull the front side of the lower fairing.
  • Pull the fairing outward while flipping the lower portion of the fairing.
• Remove the lower faring [D].

• If necessary, separate the lower fairings by removing the screws [A].

Lower Fairing Installation

• Insert the hooks [A] into the slots [B].
• Install:
  Screws and Bolt
  Quick Rivets
  Rear Fairing Cover (see Rear Fairing Cover Installation)
  Floor Mat

Front Fairing Removal

• Remove:
  Front Center Cover (see Front Center Cover Removal)
  Lower Fairing (see Lower Fairing Removal)
  Quick Rivets [A] (Both Sides)
  Screw [B] (Both Sides)

• Remove the nuts [A].

• Pull the lower side of the front fairing outward [A] to clear the hooks [B], and then pull the front fairing [C] forward [D] to clear the hooks [E].

• Disconnect the headlight lead connectors [A] and remove the front fairing.

Front Fairing Installation

• Connect the headlight lead connectors.
• Insert the hooks [A] of the upper side into the slots [B], and then insert the hooks [C] of the lower side into the slots [D].
• Install:
  Quick Rivets
  Screws and Nuts
• Install the removed parts (see appropriate chapters).

Front Fairing Disassembly

• Remove:
  Screws [A]
  Fitting [B]
  Inner Cover [C]

• Disconnect the front turn signal light lead connectors [A].
• Remove:
  Screws [B]
  Headlight Assy [C]

• Remove the screws [A] and separate the front fairings.

Rear Fairing Removal

• Remove:
  Storage Box (see Storage Box Removal)
  Fuel Tank Cap Cover (see Fuel Tank Cap Cover Removal)
  Rear Fairing Cover (see Rear Fairing Cover Removal)
  Grab Rail (see Grab Rail Removal)
  Bolts [A]

• Slide the rear fairing [A] backward [B], and then pull the rear fairing upward [C] to clear the hooks [D].

• Disconnect the tail/brake light lead connector [A] and remove the rear fairing.

Rear Fairing Installation

• Connect the tail/brake light lead connector.
• Insert the hooks [A] into the slots [B].
• Install the removed parts (see appropriate chapters).

Rear Fairing Disassembly

• Disconnect the license plate light lead connector [A].
• Remove:
  Screws [B]
  Tail/Brake Light Assy [C]

• Remove the screws [A] and separate the rear fairings [B] and flap/rear fender [C].

Side Fairing Removal

• Remove:
  Front Fairing (see Front Fairing Removal)
  Rear Fairing (see Rear Fairing Removal)
  Footpeg (see Footpeg Removal)
  Bolts [A]

• Pull the side fairing [A] upward [B] to clear the hooks [C].

• Clear the plate [A] of the leg shield from bolt hole [B] of the side fairing.

• Remove the side fairing.

• If necessary, separate the side fairing [A], inner cover [B] and floor board [C] by removing the screws [D].

Side Fairing Installation

• Insert the hooks [A] into the slots [B].
• Tighten the bolts.
• Install the removed parts (see appropriate chapters).

See also: