Peugeot Satelis - Service manual > Removal of the storage compartment
Procedure 4.
- Remove the side fairings. See: Procedure 3.
- Disconnect the plate light and the saddle opening contact switch.
- Remove the storage compartment. (4 screws and 2 nuts).
When dismantling the
splash guard, fit the screws with standard thread lock.
Removal of the tank covers
Procedure 5.
- The rider's saddle. See: Procedure 1.
- Open the tank filler cap door.
- Remove the 4 screws that secure the rear panel.
- Remove the upper fairing.
- Remove the utility hanger. (2 screw).
- Remove 1 nut and 2 screws that secure the lower fairing.
- Remove the screw that secures the rear cover / footboard on each side of the vehicle. (1)
- Push slightly aside the cover / footboard assembly and remover the fuel tank cover panel by sliding it backwards.
Removal of a RH or LH footboard
Procedure 6.
- Remove the tank cover panel. See: Procedure 5.
- Remove the footboard mat.
- On each side remove:
- 8 plastic screws. (1)
- 3 washer head screws. Ø6 mm. (2)
- washer head screw. Ø5 mm. (3)
- Press on the underbody panel in order to separate it from the footboard. (A)
- Separate the footboard from the rear fairing and bracket that anchors it to the body. (B)
- Separate the front of the footboard which is linked to the rear part of the leg shield panel. (C)
Removal of the front top cover panel
Procedure 7.
- Remove the front top cover panel. (4 screw).
Removal of the headlight and sidelight assemblies
Removal of the headlight bulbs
- Remove the front top cover panel. See: Procedure 7.
- To reach the bulbs, remove the headlight. (3 screw)
Removal of the front shield panel
Procedure 8.
- Remove the front top cover panel. See: Procedure 7.
- On each side remove:
- 2 plastic screws that secure the front leg shield to the underbody cover. (1)
- 2 plastic screws that secure the footboard to the underbody cover. (2)
- Push aside the underbody cover to reach the screw that secures the front shield panel. (3)
- On each side remove:
- 5 plastic screws. (4)
- 1 washer head screw. Ø6 mm. (5)
- 1 washer head screw. Ø5 mm. (6)
- Disconnect the headlights.
- Remove the front shield panel.
See also:
Peugeot Satelis - Service manual > Location of body components
Upper handlebar cover. Front top cover panel. Rider saddle. Lower handlebar cover. Wind protector. Tank streamlining. Counter panel. Front shield panels. Bottom panel. Footboard. Rear shield. Front mudguard. Mudguard. Rear cover. Side panels. Mudflap. Passenger backseat. Helmet compartment.
Peugeot Satelis - Service manual > Removal of the rear shield panel
Remove the ignition key. Remove the tank cover panel. See: Procedure 5. Remove the front top cover panel. See: Procedure 7. Remove: The ignition switch trim. The handlebar upper fairing (8 screw) (1). On each side remove: 2 plastic screws that secure the front leg shield to the underbody cover. 2 plastic screws that secure the footboard to the underbody cover. Push aside the underbody cover to reach the screw that secures the front shield panel. (2) On each side remove: 6 plastic screws. (3) 2 washer head screws. Ø6 mm. (4) Separate the front shield panel from the rear shield panel in order to reach the bracket that connects the rear shield panel to the footboard. (A) Pull upwards the lower part of the shield panel in order to separate it from the footboard. Relove the eyelet (B) from the shield panel and the eyelet (C) from the instrument cluster fairing in order free the rear shield panel. Topple the rear shield panel while separating it from the footboards in order to reach the header tank and the accessory plug. Remove the header tank. (Right side). Disconnect the accessory plug. (Left side). Remove the rear shield panel.
